d-series honda cam timing - for the 2ners

Discussion in 'General Motoring' started by jim beam, Sep 3, 2007.

  1. jim beam

    jim beam Guest

    for those of you who work with older d-series motors, have you ever
    wondered why the cam timing between the d16a6 cam is "half a tooth" off
    from the d15b2?

    here's what i think is the answer - [please check the math]:

    d16a6 stroke = 90mm
    d15b2 stroke = 84.5mm

    difference = 5.5mm. that's 2.75mm difference in deck height between the
    two blocks.

    how does that affect cam timing? if the deck height is different, the
    belt length between crank and cam has to be 2.75mm longer [if we're
    using the same head, which we are].

    now, diameter of the cam wheel is 114mm. radius is therefore 57mm. <-
    [you will see this number again!]

    so, if the chord of the circle is 2.75mm out, that's 2.75/57 = 0.0483
    radians difference in angle. convert radians to degrees = multiply by
    180/pi = 2.768 degrees. but, the cam/crank rotation ratio is 1:2, so
    2.768 * 2 = 5.535 degrees. there's 38 teeth to the cam gear, so 360/38
    = 9.47 degrees per tooth, so 5.5 degrees is nearly half a tooth.

    BUT!!! also note, 5.5 degrees is numerically the same as 5.5mm. why?
    180/pi = 57.298 degrees per radian, or approx. 57 degrees, close enough.
    make the cam gear 57mm radius and the 1:1 ratio gives you an easy way
    of figuring out how much to adjust the cam timing for the difference in
    deck height.

    honda engineers? smart dudes i'd say.

    how do i know all this? this weekend i went junkyard surfing and scored
    a zc cam - single cam head variety. wondering whether this was a
    bolt-on for my d15b2 crx, i wanted to check facts, so i bought a stock
    d15b2 cam as well [$14 each btw!!!]. you can see the difference in cam
    profiles [although it's not radical], but with the naked eye, you
    /can't/ see the difference in key-way angle for the cam gear. well, you
    kinda can, maybe, but it's not something you'd want to bet money on.
    so, you therefore have to measure. some blocks of wood, a spirit level,
    a school protractor, various other bits of metal for pointers, some
    messing about, and you have a measuring jig! sure enough, what is the
    angle difference in the setting of the key-way between the two cams?
    5.5 degrees. best i can measure at any rate.

    conclusion:
    the good news is that for $14 and with some good luck, you can put a hot
    cam in an old banger just for fun. the bad news is that you then have
    to spend $120 on a variable cam gear so you can account for the timing
    difference caused by the difference in deck height.

    otoh, if you work with decks and heads that have been skimmed, or
    non-stock head gaskets, you now know how to time the cam - simply
    calculate the difference in stacking height from stock in mm, and that's
    the cam timing difference in degrees. easy! don't need no dyno to
    figure this stuff out!

    next step - measure the difference in cam profile durations...
     
    jim beam, Sep 3, 2007
    #1
  2. jim beam

    jim beam Guest

    duh, mistake.
    make that a 2:1 ratio and stick with double the deck height difference.
    2.75mm deck height difference ~= 5.5 degrees timing difference. i
    think you know what i'm getting at...
     
    jim beam, Sep 3, 2007
    #2
  3. jim beam

    Tegger Guest


    You've considered that the difference in strokes may have been achieved
    simply with different crank throw offsets?

    This would be much more economical for the manufacturer than making a whole
    new block with a different deck height.
     
    Tegger, Sep 4, 2007
    #3
  4. jim beam

    jim beam Guest

    yes - i'm sure that then the belts would be the same. the d16 & d15 use
    different belts - the d16 is one tooth longer.
    sure, but all you're doing is machining the deck. that has to be done
    anyway.
     
    jim beam, Sep 4, 2007
    #4
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.