2030 Accord - caliper bolt turning direction

Miha

Usenet Archive
Joined
Mar 26, 2006
Messages
4
Reaction score
0
Hello,

Trying to change front pads on the 2003 Accord... caliper bolt is stuck dead. Just to verify... on the left side, to losen I turn clockwise (which would be counter-clockwise if looking from under the car).

Righty?

P.S. Sorry for crossposting.
 
righty tighty lefty loosey... :)

It would seem backwards from the perspective of facing the fender of the car.

Use some penetrating oil (don't get any on your barke disc or pads)

t
 
loewent said:
righty tighty lefty loosey... :)

It would seem backwards from the perspective of facing the fender of the car.

Use some penetrating oil (don't get any on your barke disc or pads)

t

After a few bad experiences stripping few key bolts... just double-checking.

So, when facing the caliper from the outside, it is to the right to loosen, correct?
 
Miha said:
After a few bad experiences stripping few key bolts... just double-checking.

So, when facing the caliper from the outside, it is to the right to loosen, correct?

I've never heard of caliper bolts being left hand thread. Only a driver side AXEL hub nut would be left hand thread.

So counter clockwise to loosen. I thought that there was just a smaller bolt to remove to SWING the caliper up to R & R the pads.
 
Alan said:
I've never heard of caliper bolts being left hand thread. Only a driver side AXEL hub nut would be left hand thread.

So counter clockwise to loosen. I thought that there was just a smaller bolt to remove to SWING the caliper up to R & R the pads.

Unless things have changed recently, the only left hand threaded fasteners that I'm aware of on a Honda are inside the transmission. Everything else is right hand threaded, i.e., tightens clockwise and loosens counter-clockwise.

Eric
 
Including that confounded crank pulley bolt... NOT reverse thread.... :)
[quoted text clipped - 7 lines]
So counter clockwise to loosen. I thought that there was just a smaller bolt to remove to SWING the caliper up to R & R the pads.

Unless things have changed recently, the only left hand threaded fasteners that I'm aware of on a Honda are inside the transmission. Everything else is right hand threaded, i.e., tightens clockwise and loosens counter-clockwise.

Eric
 
Eric said:
:
Including that confounded crank pulley bolt... NOT reverse thread.... :)

Except if you own one of these,
http://www.accoutrements.com/products/10570.html. Then you can throw that whole clockwise thing out the window...
 
Miha said:
So, when facing the caliper from the outside, it is to the right to loosen, correct?

That sounds right. I don't usually get confused, but when doing really contorted things I like to set up a ratchet to loosen, then put it on the fastener to see which way it resists.

Mike
 
Miha said:
Hello,

Trying to change front pads on the 2003 Accord... caliper bolt is stuck dead. Just to verify... on the left side, to losen I turn clockwise (which would be counter-clockwise if looking from under the car).

Do you mean the slide pins?

They unscrew the usual way.

Use a 6-point socket and a long extension. It will crack loose.

You must live in the Rust Belt.
 
Miha said:
Hello,

Trying to change front pads on the 2003 Accord... caliper bolt is stuck dead. Just to verify... on the left side, to losen I turn clockwise (which would be counter-clockwise if looking from under the car).

Do you mean the slide pins?

They unscrew the usual way.

Use a 6-point socket and a long extension. It will crack loose.

You must live in the Rust Belt.
 

Latest threads

Back
Top